A way of laying pavers that allows you to support plates directly onto grass, gravel or sand.
A way of laying pavers that allows you to create perfectly stable surfaces of incredible resistance.
* When installed over reinforced concrete (4” minimum) using a thinset/thickset mortar suitable for porcelain paver.
Traditional deck made with wood and porcelain pavers.
Slabs matched with a support structure for raised high-performing floors that also leaves sufficient room for under-floor inspection.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
The stratigraphic images are just an example of the type of application and technical features of Frontier20.
Landmark Ceramics recommends to refer to the specific norms valid in the various countries to carry out a state-of-the-art installation.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
WARNING:
Please remember that high density panel can reduce the heat dispersion accumulated by pavers exposed to direct sun or any other source of heat.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
Insure the plastic 3/16” (4 mm) spacers are installed at all corners of the installed pavers, in order to prevent pavers from touching each other (and potentially chipping) and to allow better water drainage.
The stratigraphic images are just an example of the type of application and technical features of Frontier20. Landmark Ceramics recommends to refer to the specific norms valid in the various countries to carry out a state-of-the-art installation.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
Insure the plastic 3/16” (4 mm) spacers are installed at all corners of the installed pavers, in order to prevent pavers from touching each other (and potentially chipping) and to allow better water drainage.
The stratigraphic images are just an example of the type of application and technical features of Frontier20. Landmark Ceramics recommends to refer to the specific norms valid in the various countries to carry out a state-of-the-art installation.
* It is recommended installation over 4” minimum thick reinforced concrete, using a thinset/thickset mortar suitable for porcelain paver.
THIN SET MORTAR APPLICATION OVER REINFORCED CONCRETE
PRACTICAL INSTALLATION
Follow the drawing below.
CAUTION: if a porcelain paver is installed over a control joint, the paver will refl ectively crack along the contraction/control joint beneath it.
Utilization of an uncoupling membrane can help minimize the potential issue.
The stratigraphic images are just an example of the type of application and technical features of Frontier20. Landmark Ceramics recommends to refer to the specific norms valid in the various countries to carry out a state-of-the-art installation.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
Insure the plastic 3/16” (4 mm) spacers are installed at all corners of the installed pavers, in order to prevent pavers from touching each other (and potentially chipping) and to allow better water drainage.
The stratigraphic images are just an example of the type of application and technical features of Frontier20. Landmark Ceramics recommends to refer to the specific norms valid in the various countries to carry out a state-of-the-art installation.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
(Pedestrian foot traffic)
PRACTICAL INSTALLATION
Follow the drawing below.
Insure the plastic 3/16” (4 mm) spacers are installed at all corners of the installed pavers, in order to prevent pavers from touching each other (and potentially chipping) and to allow better water drainage.
The stratigraphic images are just an example of the type of application and technical features of Frontier20. Landmark Ceramics recommends to refer to the specific norms valid in the various countries to carry out a state-of-the-art installation.
System made up of disks of variable thickness. Utilize for low height installation (up to ¾”).
System made up of adjustable height pedestal (from 1 ¼” to 16”).
Landmark products are made using the best technology available, and their technical performances match or exceed requirements from both ASTM and ISO standards for porcelain products.
Nevertheless, if the application of the 20 mm slabs requires the ceramic product used in structural installations (such as, but not limited to, raised floors), the project engineer and/or customer must carefully assess the project requirements with regard to the technical specifications of the slabs.
To prevent the risk of damage or injury, the manufacturer recommends:
• With regard to a raised floor installation a ceramic slab may fracture on impact if a heavy object falls on it. Therefore, the manufacturer recommends checking the specific intended use before starting the installation and:
1) As far as supports requirements, comply with the table for raised installation provided below.
2) In all installations on pedestals higher than 3/4", reinforcing must be applied on the back of the slabs (double fiberglass mesh) supplied and applied by the manufacturer.
• With reference to any dry installation system of flooring above the ground level, the manufacturer recommends to comply with local regulations and conditions of use with regard to wind-load, loadbearing, seismic events, etc.
• Outdoor pavings installed unglued above the ground level are subject to the action of the wind, with the risk, in some cases, of becoming airborne. The manufacturer recommends to require the assistance of a qualified professional in order to check the suitability of the installation system above the ground adopted, in accordance with the local laws and regulations and the conditions of use.
• It is recommended to carry out raised installation onto a solid, resistant substrate with the correct inclination to guarantee water drainage. Support come equipped with four spacers that allow for the creation of grout lines between pavers. For a correct installation against walls or corners, it is necessary to keep the supports distant from the wall and remove 2 or 4 spacers as showed in the picture below. Landmark Ceramics recommends to strictly follow the instructions for the raised installation of Frontier20.
Failure to comply with these recommendations may lead to improper use of the product and could cause serious property damage or injury. Additionally, failure to comply with these recommendations will result in the Warranty provided herein becoming null and void.
NOTE: For any detail and technical specification concerning the double fiberglass mesh, please contact Landmark Ceramics. Landmark is responsible only if it supplies the whole system (paver + double fiber mesh). Landmark cannot be held responsible for reinforcing systems not supplied by Landmark.Outdoor pavers installed unglued above the ground level are subject to the action of the wind, with the risk, in some cases, of becoming airborne. The manufacturer recommends to require the assistance of a qualified professional in order to check the suitability of the installation system above the ground adopted, in accordance with the local laws and regulations and the conditions of use. Failure to do so could result in serious injury or property damage.
If the application of the 20 mm slabs requires the ceramic product used in structural installations, the project engineer and/or customer must carefully assess the project requirements with regard to the technical specifications of the slabs. With reference to a raised floor installation: a ceramic slab may fracture on impact if a heavy object falls on it from any significant height. Therefore, to prevent the risk of damage or injury, Landmark recommends to check the specific intended use before starting the installation and to follow table for raised installation provided below. In certain conditions, reinforcing must be applied on the back of the slabs (double fiberglass mesh) supplied and applied by the Landmark. With reference to any dry installation system of flooring above the ground level: Landmark recommends to comply with local regulations and conditions of use with regard to wind- load, loadbearing, seismic events, etc. Failure to comply with these recommendations may lead to improper use of the product and could cause serious damage or injury. Failure to adhere to Landmark’s instructions for installation of slabs on raised pedestal systems may result in serious injury.